Zilog Z80180 Bedienungsanleitung Seite 264
- Seite / 326
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Z8018x
Family MPU User Manual
248
UM005003-0703
Note 1: (HL) replaces g.
Note 2: (HL) replaces s.
Note 3: If DDH is supplemented as first Op Code for the instructions
which have HL or (HL) as an operand in Table 48, the instructions are
executed replacing HL with IX and (HL) with (IX+d).
ex. 22H : LD (mn), HL
DDH 22H : LD (mn), IX
If FDH is supplemented as 1st Op Code for the instructions which have
HL or (HL) as an operand in Table 48, the instructions are executed
replacing HL with IY and (HL) with (IY+d).
ex. 34H : INC (HL)
FDH 34H : INC (IY+d)
However, JP (HL) and EX DE, HL are exceptions and note the following.
•
If DDH is supplemented as 1st Op Code for JP (HL), (IX) replaces
(HL) as operand and JP (IX) is executed
•
If FDH is supplemented as 1st Op Code for JP (HL), (IY) replaces
(HL) as operand and JP (IY) is executed
•
Even if DDH or FDH is supplemented as 1st Op Code for EX DE,
HL, HL is not replaced and the instruction is regarded as illegal
instruction.
- Family MPU 1
- MANUAL OBJECTIVES 3
- Intended Audience 3
- Manual Organization 3
- Sections 4
- Appendices 4
- Table of Contents 5
- List of Figures 8
- UM005003-0703 10
- List of Tables 12
- Status Signals 287 14
- FEATURES 16
- GENERAL DESCRIPTION 16
- PIN DESCRIPTION 22
- ARCHITECTURE 27
- OPERATION MODES 30
- 0 and IOC is 0 32
- CPU Timing 33
- Wait State Generator 42
- Bit 7 6 5 4 44
- MWI1 MWI0 MWI1 MWI0 44
- R/W R/W R/W R/W 44
- 1, selecting the 45
- Processors Only) 46
- SLP 2nd Op Code address 50
- Add-On Features 51
- STANDBY Mode 52
- IDLE Mode 55
- STANDBY-QUICK RECOVERY Mode 56
- Internal I/O Registers 56
- –0 Reserved ? ? Reserved 67
- Memory Management Unit (MMU) 69
- Figure 25. MMU Block Diagram 71
- 0 during I/O cycles 72
- MMU Register Description 75
- 0 during RESET 77
- 1 while all bits 78
- 0. The logical 64KB 78
- 0000H to FFFFH) 78
- Interrupts 80
- Interrupt Vector Low Register 81
- 00H during RESET 82
- N/A R/W R/W R/W 83
- 1 by the El (Enable 84
- 00000H was caused by 85
- INT0 Mode 0 90
- INT0 Mode 1 91
- INT0 Mode 2 93
- 00H and 94
- INT1, INT2 95
- 0. Each is also 96
- Family MPU User Manual 100
- Dynamic RAM Refresh Control 101
- TR1 TRW* TR2 102
- DMA Controller (DMAC) 105
- 107
- DMAC Register Description 108
- DMA Register Description 118
- Bits 5–3 119
- Bits 2–0 119
- DMA Operation 119
- Memory to Memory—Channel 0 120
- 00H) transfer 122
- Memory to ASCI - Channel 0 124
- Note: X = Don’t care 125
- T1 T2 T3 T3T2T1 130
- Processors 131
- ASCI Register Description 132
- 08H, 09H) 134
- 1) these pins 149
- 1, then the CKA1/ 149
- 0. Even after the 154
- Figure 56. ASCI Clock 156
- Baud Rate Generator 158
- CSI/O Block Diagram 161
- CSI/O Registers Description 162
- Address = 0BH) 164
- Interrupt Request 166
- = 0) when 167
- PRT Block Diagram 171
- PRT Register Description 172
- 0FH, CHI, 16H, 17H) 174
- Timer Control Register (TCR) 176
- PRT Interrupts 179
- PRT and RESET 179
- Secondary Bus Interface 180
- On-Chip Clock Generator 183
- Miscellaneous 187
- Software Architecture 188
- CPU REGISTERS 190
- Accumulator (A, A') 191
- Flag Registers (F, F') 192
- Interrupt Vector Register (I) 192
- R Counter (R) 192
- Index Registers (IX, and IY) 192
- Stack Pointer (SP) 193
- Program Counter (PC) 193
- Flag Register (F) 193
- Addressing Modes 195
- Implied Register (IMP) 195
- Register Direct (REG) 195
- Register Indirect (REG) 196
- Indexed (INDX) 197
- Extended (EXT) 197
- Immediate (IMMED) 198
- Relative (REL) 198
- IO (I/O) 199
- DC Characteristics 200
- Z80180 DC CHARACTERISTICS 201
- Z8S180 DC CHARACTERISTICS 202
- Z8L180 DC CHARACTERISTICS 204
- AC Characteristics 208
- Timing Diagrams 213
- STANDARD TEST CONDITIONS 221
- Instruction Set 223
- CONDITION 224
- RESTART ADDRESS 225
- MISCELLANEOUS 226
- DATA TRANSFER INSTRUCTIONS 238
- Special Control Instructions 251
- Instruction Summary 253
- Op Code Map 263
- DDH 22H : LD (mn), IX 264
- Bus Control Signal Conditions 267
- INTERRUPTS 295
- Operating Modes Summary 297
- REQUEST PRIORITY 298
- OPERATION MODE TRANSITION 299
- 0000H (all DMA transfers) 301
- Status Signals 303
- PIN STATUS 304
- –A17, A19 — Z 1 A 1 305
- –D7— ZZAZ 305
- INTERNAL I/O REGISTERS 309
- Ch 0 Destination Mode 1,0 315
- ORDERING INFORMATION 319
Verwandte Produkte und Handbücher für Sensoren Zilog Z80180
Sensoren Zilog Z86193 Bedienungsanleitung
(260 Seiten)
(260 Seiten)
Sensoren Zilog Z86C36 Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Sensoren Zilog Z86E07 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Sensoren Zilog Z08470 Bedienungsanleitung
(326 Seiten)
(326 Seiten)
Sensoren Zilog Z08470 Bedienungsanleitung
(330 Seiten)
(330 Seiten)
Sensoren Zilog Z8PE002 Bedienungsanleitung
(48 Seiten)
(48 Seiten)
Sensoren Zilog Z8PE002 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Sensoren Zilog Z8FS021A Bedienungsanleitung
(25 Seiten)
(25 Seiten)
Sensoren Zilog ZEPIR0BA Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Sensoren Zilog EZ80F91GA Bedienungsanleitung
(127 Seiten)
(127 Seiten)
Sensoren Zilog ZMOT0BHH Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Sensoren Zilog Z16FMC2 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Sensoren Zilog Z16FMC2 Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Sensoren Zilog ZAURA868 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Sensoren Zilog Z80230 Bedienungsanleitung
(394 Seiten)
(394 Seiten)
Sensoren Zilog ZAURCT Bedienungsanleitung
(59 Seiten)
(59 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern