Zilog Z86193 Bedienungsanleitung Seite 228
- Seite / 260
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Z8
®
CPU
User Manual
UM001604-0108 Instruction Description
221
Rotate Left Through Carry
Syntax
RLC dst
Instruction Format
Operation
C← dst(7)
dst(0) ← C
dst(1) ← dst(0)
dst(2) ← dst(1)
dst(3) ← dst(2)
dst(4) ← dst(3)
dst(5) ← dst(4)
dst(6) ← dst(5)
dst(7) ← dst(6)
The contents of the destination operand along with the C Flag are rotated left by one bit
position. The initial value of bit 7 replaces the C Flag and the initial value of the C Flag
replaces bit 0, as shown below.
Address modes R or IR can be used to specify a 4-bit Working Register. In this format, the
destination Working Register operand is specified by adding
1110b (Eh) to the high nibble
Cycles
OPC
(Hex)
Address Mode
dst
OPC dst
610 R
611 IR
Flag Description
C Set if the bit rotated from the most significant bit position was 1
(i.e., bit 7 was 1).
Z Set if the result is zero; cleared otherwise.
S Set if the result bit 7 is set; cleared otherwise.
V Set if arithmetic overflow occurred (if the sign of the destination
operand changed during rotation); cleared otherwise.
D Unaffected
H Unaffected
C D7D6D5D4D3D2D1D0
Note:
- Z8 Family of Microcontrollers 1
- UM001604-0108 2
- DO NOT USE IN LIFE SUPPORT 2
- LIFE SUPPORT POLICY 2
- As used herein 2
- Document Disclaimer 2
- Revision History 3
- Table of Contents 4
- Table of Contents 5
- Product Development Support 10
- UM001604-0108 Z8 11
- CPU Product Overview 11
- Address Space 12
- Address Space 13
- General-Purpose Registers 14
- RAM Protect 14
- Working Register Groups 14
- Error Conditions 17
- Standard Z8 Registers 22
- Expanded Z8 Registers 23
- Program Memory 26
- External Memory 27
- External Data Memory 28
- Clock Control 31
- External Clock Divide-By-Two 32
- Oscillator Control 33
- Oscillator Operation 34
- Circuit Board Design Rules 35
- Crystals and Resonators 36
- UM001604-0108 Clock 37
- Figure 19. LC Clock 37
- LC Oscillator 38
- RC Oscillator 39
- UM001604-0108 Reset 40
- Figure 22. Reset Timing 42
- User Manual 43
- Watchdog Timer 48
- Power-On Reset 49
- Input/Output Ports 50
- Input and Output Registers 51
- General I/O Mode 52
- Input/Output Ports 53
- Read/Write Operations 54
- Handshake Operation 54
- Handshake Operations 58
- General Port I/O 59
- Special Functions 68
- Port Handshake 70
- I/O Port Reset Conditions 73
- Analog Comparators 75
- Comparator Programming 78
- Comparator Operation 79
- Comparator Definitions 79
- Open-Drain Configuration 80
- Low EMI Emission 81
- Input Protection 82
- CMOS Autolatches 84
- Autolatch Model 85
- Design Considerations 85
- Counters and Timers 87
- Prescalers and Counter/Timers 88
- Counter/Timer Operation 90
- Prescaler Operations 91
- External Clock Input Mode 96
- Gated Internal Clock Mode 97
- Triggered Input Mode 97
- Cascading Counter/Timers 98
- Counters and Timers 100
- Interrupts 102
- Interrupt Sources 103
- External Interrupt Sources 104
- Internal Interrupt Sources 105
- Interrupt Initialization 106
- Interrupts 107
- Reset Conditions 116
- Power-Down Modes 117
- Power-Down Modes 118
- Stop Mode Recovery Register 119
- Serial Input/Output 122
- UART Bit-Rate Generation 123
- Serial Input/Output 124
- UART Receiver Operation 125
- Overwrites 126
- Framing Errors 126
- Transmitter Operation 127
- UART Reset Conditions 129
- Serial Peripheral Interface 129
- SPI Operation 132
- SPI Compare 132
- SPI Clock 132
- External Interface 138
- External Interface 139
- External Stacks 140
- Data Memory 141
- Bus Operation 141
- Address Strobe 143
- Data Strobe 143
- Extended Bus Timing 144
- Instruction Timing 145
- Reset Conditions 147
- Instruction Set 148
- Instruction Set 149
- Processor Flags 151
- Zero Flag 152
- Sign Flag 152
- Overflow Flag 152
- Decimal Adjust Flag 152
- Condition Codes 153
- Notation and Binary Encoding 154
- Assembly Language Syntax 156
- Instruction Summary 157
- Op Code Map 163
- Instruction Description 164
- Instruction Description 165
- Add With Carry 168
- Call Procedure 171
- Complement Carry Flag 173
- Complement 175
- Decimal Adjust 179
- Decrement 182
- Decrement Word 185
- Disable Interrupts 187
- Enable Interrupts 188
- Increment 190
- Increment Word 192
- Interrupt Return 194
- Jump Relative 197
- Load Constant 202
- Load Constant Autoincrement 204
- Load External Data 206
- No Operation 210
- Logical AND 211
- Logical OR 214
- Logical Exclusive OR 217
- Reset Carry Flag 224
- C D7D6D5D4D3D2D1D0 226
- CD7 D6 D5 D4 D3 D2 D1 D0 230
- Set Carry Flag 234
- Set Register Pointer 235
- Subtract 241
- Subtract With Carry 244
- Swap Nibbles 247
- Test Complement Under Mask 249
- Test Under Mask 252
- Watchdog Timer 255
- UM001604-0108 Index 257
- Customer Support 260
Verwandte Produkte und Handbücher für Sensoren Zilog Z86193
Sensoren Zilog Z86C36 Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Sensoren Zilog Z86E07 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Sensoren Zilog Z08470 Bedienungsanleitung
(326 Seiten)
(326 Seiten)
Sensoren Zilog Z08470 Bedienungsanleitung
(330 Seiten)
(330 Seiten)
Sensoren Zilog Z8PE002 Bedienungsanleitung
(48 Seiten)
(48 Seiten)
Sensoren Zilog Z8PE002 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Sensoren Zilog Z8FS021A Bedienungsanleitung
(25 Seiten)
(25 Seiten)
Sensoren Zilog ZEPIR0BA Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Sensoren Zilog EZ80F91GA Bedienungsanleitung
(127 Seiten)
(127 Seiten)
Sensoren Zilog ZMOT0BHH Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Sensoren Zilog Z16FMC2 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Sensoren Zilog Z16FMC2 Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Sensoren Zilog ZAURA868 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Sensoren Zilog Z80230 Bedienungsanleitung
(394 Seiten)
(394 Seiten)
Sensoren Zilog ZAURCT Bedienungsanleitung
(59 Seiten)
(59 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern