
7-18
Z16C30 USC
®
USER'S MANUAL
UM97USC0100
ZILOG
7.11.2 Receive Data Interrupts (Continued)
7.11.3 Transmit Status Interrupt Sources
and IA Bits
The interrupt logic can set the Transmit Status IP bit in
response to any of six interrupt sources. Software can read
the status of each source in the LSByte of the Transmit
Command/Status Register (TCSR), which is shown in
Figure 7-12. The following descriptions of the TCSR bits
are similar to those in the 'Detailed Status in the TCSR'
section of Chapter 5.
PreSent The interrupt logic can set the TS IP bit
when this bit (TCSR7) goes from a 0 to
a 1, because the transmitter has fin-
ished sending the “Preamble” se-
lected in the Channel Control Regis-
ter (CCR11-8) in a synchronous mode.
IdleSent The interrupt logic can set the TS IP bit
when this bit (TCSR6) goes from a 0 to
a 1, because the transmitter has sent
the idle line state selected by the
TxIdle field (TCSR10-8). If TxIdle and
TxMode specify the condition as Flags
or Syncs, this bit can be set for each
one sent. Otherwise, for bit-oriented
Idle conditions, it’s set only after the
first bit is sent.
AbortSent The interrupt logic can set the TS IP bit
in HDLC/SDLC mode, when this bit
(TCSR5) goes from 0 to 1 because the
transmitter has sent an Abort charac-
ter.
EOF/EOM Sent The interrupt logic can set the TS IP bit
in a synchronous mode, when this bit
(TCSR4) goes from 0 to 1 because the
transmitter has sent the closing Flag
or Sync character at the end of a
message or frame.
CRCSent The interrupt logic can set the TS IP bit
in a sync mode, when this bit (TCSR3)
goes from 0 to 1 because the trans-
mitter has sent the CRC sequence
just before the end of a message or
frame.
TxUnder The interrupt logic can set the TS IP bit
when this bit (TCSR1) goes from 0 to
1, because the transmitter needed a
character from the TxFIFO but it was
empty.
Once one of these TCSR bits is 1, it must be cleared to 0
by writing a 1 to that bit position in TCSR.
In order to ensure that future interrupts are requested
properly when more than one Transmit Status condition is
Armed in the TICR, a Transmit Status interrupt service
routine must clear all of the IA bits in the TICR and then set
the desired ones again, after it has cleared the TS IP bit and
the TCSR bits that it has serviced.
Each of these six sources has a separate Interrupt Arm
(IA) bit in the LSByte of the Transmit Interrupt Control
Register (TICR). Figure 7-13 shows the TICR. If an IA bit is
1, the interrupt logic sets the Transmit Status IP bit when
14 13 12 11 10 9 8 7 6 5 4 3 2 1 015
Pre
Sent IA
Idle
Sent
IA
Abort
Sent
IA
EOF/
EOM
Sent IA
CRC
Sent
IA
Wait2
Send
Tx
Under
IA
TC1R
Sel
"TxFIFOStatus" if last TCSR 15-12 command 4-7 was 5
"Tx Int level" if last RCSR 15-12 command 4-7 was 6
"Tx DMA Req level" If last TCSR 15-12 command 4-7 was 7
Figure 7-13. The Transmit Interrupt Control Register (TICR)
14 13 12 11 10 9 8 7 6 5 4 3 2 1 015
TCmd Rsrvd Txidle
Pre
Sent
Idle
Sent
Abort
Sent
EOF/
EOM
Sent
CRC
Sent
All
Sent
Tx
Under
Tx
Empty
Figure 7-12. The Transmit Command/Status Register (TCSR)
Kommentare zu diesen Handbüchern