Copyright ©2008 by Zilog®, Inc. All rights reserved.www.zilog.comZ8 Encore! XP® F64xx Series Flash MicrocontrollersIn-Circuit EmulatorUser ManualUM016
In-Circuit EmulatorUser ManualUM016804-02087F64xx Series ICE, you must either change the PC’s Ethernet settings to match those of the Z8 Encore! XP® F
In-Circuit EmulatorUser ManualUM016804-02088Figure 6. The Network Dialog Box2. In the panel labeled LAN or High-Speed Internet, double-click the Local
In-Circuit EmulatorUser ManualUM016804-02089Figure 7. The Local Area Connection Status Dialog Box3. In the Local Area Connection Status dialog box, cl
In-Circuit EmulatorUser ManualUM016804-020810Figure 8. The Local Area Connection Properties Dialog Box4. In the panel labeled This connection uses the
In-Circuit EmulatorUser ManualUM016804-020811Figure 9. The Internet Protocol Properties Dialog Box5. Enter values for the IP address and subnet mask t
In-Circuit EmulatorUser ManualUM016804-020812Changing Z8 Encore! XP® F64xx Series ICE Settings to Match the PC1. Connect the PC serial port to the Z8
In-Circuit EmulatorUser ManualUM016804-020813Zilog TCP/IP Software Suite v1.1Copyright (C) 2003 Zilog Inc.All Rights Reservedclock enabledIP Address:
In-Circuit EmulatorUser ManualUM016804-020814 R Reset emulator>8. Use the I command to change the Z8 Encore! XP® F64xx Series ICE IP address t
In-Circuit EmulatorUser ManualUM016804-020815The following procedures require that the emulator be connected to a target board, such as the Z8 Encore!
In-Circuit EmulatorUser ManualUM016804-0208168. Select the appropriate clock frequency or enter the clock frequency in the Other field. This should ma
In-Circuit EmulatorUser ManualUM016804-0208 Revision HistoryiiRevision HistoryEach instance in the Revision History table reflects a change to this do
In-Circuit EmulatorUser ManualUM016804-020817Using Events to Start and Stop a Trace1. Now we’ll define a pair of events to automatically start and sto
In-Circuit EmulatorUser ManualUM016804-02081813. Click Get Frames to display the trace information. Study the contents of the Trace window to see how
In-Circuit EmulatorUser ManualUM016804-0208192. In the Memory window, double-click the value you want to change and type in a new value. (Values begin
In-Circuit EmulatorUser ManualUM016804-020820External Interface ConnectorsThere are four external interface connectors on the Z8 Encore! XP® F64xx Ser
In-Circuit EmulatorUser ManualUM016804-020821gles (changes state) or pulses, depending on what you specified for Trigger Out.How to Set Connector J11
In-Circuit EmulatorUser ManualUM016804-020822•Z8F64220100ZDV, Z8 Encore! XP® F64xx Series 68-pin PLCC ICE Adapter•Z8F64230100ZDF, Z8 Encore! XP® F64xx
In-Circuit EmulatorUser ManualUM016804-020823Customer SupportFor answers to technical questions about the product, documentation, or any other issues
In-Circuit EmulatorUser ManualUM016804-020824DO NOT USE IN LIFE SUPPORTLIFE SUPPORT POLICYZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
In-Circuit EmulatorUser ManualUM016804-0208 Table of ContentsiiiTable of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In-Circuit EmulatorUser ManualUM016804-02081IntroductionThe Zilog Z8 Encore! XP® F64xx Series In-Circuit Emulator (ICE) pro-vides Z8 Encore! XP® F64xx
In-Circuit EmulatorUser Manual2UM016804-0208RequirementsTable 1 lists the PC requirements for running ZDS II.Install the SoftwareFollow these steps to
In-Circuit EmulatorUser ManualUM016804-02083installing the package adapter that came with your kit into the compatible socket on a target board such a
In-Circuit EmulatorUser ManualUM016804-02084Figure 2. Z8 Encore! XP® F64xx Series ICE Rear Panel4. Connect the ribbon cables from the target POD to co
In-Circuit EmulatorUser ManualUM016804-02085Figure 3. Connecting the Z8 Encore! XP® F64xx Series ICE to the Target POD and Adapter Assembly (Typical C
In-Circuit EmulatorUser ManualUM016804-02086Figure 5. Z8 Encore! XP® F64xx Series ICE Front-PanelConfigure the HardwareConfiguring the Z8 Encore! XP®
Kommentare zu diesen Handbüchern